RFID mit dem Arduino programmieren: Unterschied zwischen den Versionen

Aus DDSWiki
Wechseln zu: Navigation, Suche
(→‎Referenzen und Links)
Zeile 6: Zeile 6:
 
* MFRC522 --> Diese Library muss bei Verwendung der Arduino IDE mit Hilfe des Library Managers installiert werden
 
* MFRC522 --> Diese Library muss bei Verwendung der Arduino IDE mit Hilfe des Library Managers installiert werden
 
* [https://de.wikipedia.org/wiki/Serial_Peripheral_Interface SPI Erklärung auf Wikipedia]
 
* [https://de.wikipedia.org/wiki/Serial_Peripheral_Interface SPI Erklärung auf Wikipedia]
 +
 +
= Video Erklärung =
 +
 +
== Der Code zum Video ==
 +
<pre>
 +
 +
#include <MFRC522.h>
 +
 +
#define SS_PIN 10
 +
#define RST_PIN 13
 +
 +
MFRC522 rfid(SS_PIN, RST_PIN); // Instance of the class
 +
 +
MFRC522::MIFARE_Key key;
 +
 +
// Init array that will store new NUID
 +
byte nuidPICC[4];
 +
 +
 +
void setup() {
 +
 +
 +
  //while (!Serial);
 +
  Serial.begin(9600);
 +
 +
 +
  SPI.begin(); // Init SPI bus
 +
  rfid.PCD_Init(); // Init MFRC522
 +
 +
  //for (byte i = 0; i < 6; i++) {
 +
  //  key.keyByte[i] = 0xFF;
 +
  //}
 +
 +
  //Serial.println(F("This code scan the MIFARE Classsic NUID."));
 +
  //Serial.print(F("Using the following key:"));
 +
  //printHex(key.keyByte, MFRC522::MF_KEY_SIZE);
 +
 +
 +
 +
}
 +
 +
void loop() {
 +
  checkRFID();
 +
}
 +
 +
 +
void checkRFID() {
 +
  //Serial.println("Checking RFID");
 +
  // RFID Reader
 +
  // Reset the loop if no new card present on the sensor/reader. This saves the entire process when idle.
 +
  if ( ! rfid.PICC_IsNewCardPresent())
 +
    return;
 +
 +
  // Verify if the NUID has been readed
 +
  if ( ! rfid.PICC_ReadCardSerial())
 +
    return;
 +
 +
  //Serial.print(F("PICC type: "));
 +
  MFRC522::PICC_Type piccType = rfid.PICC_GetType(rfid.uid.sak);
 +
  //Serial.println(rfid.PICC_GetTypeName(piccType));
 +
 +
  // Check is the PICC of Classic MIFARE type
 +
  if (piccType != MFRC522::PICC_TYPE_MIFARE_MINI &&
 +
      piccType != MFRC522::PICC_TYPE_MIFARE_1K &&
 +
      piccType != MFRC522::PICC_TYPE_MIFARE_4K) {
 +
    Serial.println(F("Your tag is not of type MIFARE Classic."));
 +
    return;
 +
  }
 +
 +
 +
  printDec(rfid.uid.uidByte, rfid.uid.size);
 +
 +
  rfid.PICC_HaltA();
 +
 +
  // Stop encryption on PCD
 +
  rfid.PCD_StopCrypto1();
 +
}
 +
 +
/**
 +
  Helper routine to dump a byte array as hex values to Serial.
 +
*/
 +
void printHex(byte *buffer, byte bufferSize) {
 +
  for (byte i = 0; i < bufferSize; i++) {
 +
    Serial.print(buffer[i] < 0x10 ? " 0" : " ");
 +
    Serial.print(buffer[i], HEX);
 +
  }
 +
}
 +
 +
/**
 +
  Helper routine to dump a byte array as dec values to Serial.
 +
*/
 +
void printDec(byte *buffer, byte bufferSize) {
 +
  Serial.println("Printing RFID Tag");
 +
 +
  for (byte i = 0; i < bufferSize; i++) {
 +
    //Serial.print(buffer[i] < 0x10 ? " 0" : " ");
 +
    Serial.print(buffer[i], DEC);
 +
  }
 +
 +
  Serial.println();
 +
}
 +
</pre>

Version vom 24. August 2020, 14:02 Uhr

Bitte erst alle Kabel (Juper Wire) aufbauen, dann den Arduino über USB-Kabel anstecken. Ansonsten kann es sein, dass es nicht funktioniert.

Rfidreader.png

Hinweise

  • MFRC522 --> Diese Library muss bei Verwendung der Arduino IDE mit Hilfe des Library Managers installiert werden
  • SPI Erklärung auf Wikipedia

Video Erklärung

Der Code zum Video


#include <MFRC522.h>

#define SS_PIN 10
#define RST_PIN 13

MFRC522 rfid(SS_PIN, RST_PIN); // Instance of the class

MFRC522::MIFARE_Key key;

// Init array that will store new NUID
byte nuidPICC[4];


void setup() {


  //while (!Serial);
  Serial.begin(9600);


  SPI.begin(); // Init SPI bus
  rfid.PCD_Init(); // Init MFRC522

  //for (byte i = 0; i < 6; i++) {
  //  key.keyByte[i] = 0xFF;
  //}

  //Serial.println(F("This code scan the MIFARE Classsic NUID."));
  //Serial.print(F("Using the following key:"));
  //printHex(key.keyByte, MFRC522::MF_KEY_SIZE);



}

void loop() {
  checkRFID();
}


void checkRFID() {
  //Serial.println("Checking RFID");
  // RFID Reader
  // Reset the loop if no new card present on the sensor/reader. This saves the entire process when idle.
  if ( ! rfid.PICC_IsNewCardPresent())
    return;

  // Verify if the NUID has been readed
  if ( ! rfid.PICC_ReadCardSerial())
    return;

  //Serial.print(F("PICC type: "));
  MFRC522::PICC_Type piccType = rfid.PICC_GetType(rfid.uid.sak);
  //Serial.println(rfid.PICC_GetTypeName(piccType));

  // Check is the PICC of Classic MIFARE type
  if (piccType != MFRC522::PICC_TYPE_MIFARE_MINI &&
      piccType != MFRC522::PICC_TYPE_MIFARE_1K &&
      piccType != MFRC522::PICC_TYPE_MIFARE_4K) {
    Serial.println(F("Your tag is not of type MIFARE Classic."));
    return;
  }


  printDec(rfid.uid.uidByte, rfid.uid.size);

  rfid.PICC_HaltA();

  // Stop encryption on PCD
  rfid.PCD_StopCrypto1();
}

/**
   Helper routine to dump a byte array as hex values to Serial.
*/
void printHex(byte *buffer, byte bufferSize) {
  for (byte i = 0; i < bufferSize; i++) {
    Serial.print(buffer[i] < 0x10 ? " 0" : " ");
    Serial.print(buffer[i], HEX);
  }
}

/**
   Helper routine to dump a byte array as dec values to Serial.
*/
void printDec(byte *buffer, byte bufferSize) {
  Serial.println("Printing RFID Tag");

  for (byte i = 0; i < bufferSize; i++) {
    //Serial.print(buffer[i] < 0x10 ? " 0" : " ");
    Serial.print(buffer[i], DEC);
  }

  Serial.println();
}
Abgerufen von „https://wutevr.de/ddswiki/index.php?title=RFID_mit_dem_Arduino_programmieren&oldid=1136“